Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes

Parts & Accessories

Zipp Tangente Tube Wrench
$7.00
Zipp Speed Weaponry Valve Extender Wrench Set - Two 4 mm and 5 mm combination wrenches - Replacement wrenches required to properly install Zipp integrated valve extenders - Use with Zipp Tangente tubes with aluminum Presta valve and aluminum valve extender
Whisky Parts Co. Tubeless Conversion Rim Tape Kits
$8.00 - $16.00
Whisky Parts Co. Tubeless Rim Tape.
Zipp Cognition Freehub Kit
$133.00
Freehub bodies for Zipp Cognition hubs.
Robert Axle Project Trainer Thru Axle
$54.00
Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.
Shimano Alfine SG-S700 Right Lock Washer Seal
$4.00
Do you need to replace the right lock washer seal on your Alfine SG-S700 internally geared hub? If you're not sure, it might not be a bad idea, as contamination from damaged or worn seals is the kryptonite of virtually maintenance-free internally geared hubs.
Shimano Alfine S7000/S700 Shift Cable Fixing Bolt Unit
$4.00
Need a Shift Cable Fixing Bolt Unit for your Alfine S7000/S700 hub? Here it is. Now, get that bike back on the road!
Shimano Alfine S7000 Cassette Joint Unit
$15.00
Shimano Nexus and Alfine Internally Geared Hub Cassette Joints - Shimano model # CJ-S7000 - Does not include cable fixing bolt unit - OEM cassette joint unit for Alfine SG-S7000-8
Zipp Decal Set
$20.00
These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.
Wheels Manufacturing Inc. Outer Axle Nut
$1.25 - $5.75
Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually
Robert Axle Project BOB Trailer Thru Axle
$62.00 - $69.00
Yes! A 12mm thru-axle adapter for BOB Trailers. These Robert Axles for BOB Trailers are specifically engineered to attach the proven BOB Trailer to your thru-axle-equipped bike. Take full advantage of your modern bike with 12mm thru-axles and harness the rigidity of the thru-axle to haul your BOB Trailer. Set out on any adventure, big or small. Great for off-road tours, trail building, hauling cargo, and more! - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The axle ends are stainless steel which allows for mounting of the BOB Trailer bobbins. - No special tools required. The design allows for wheel installation or removal using your standard 5mm hex wrench. - Please note: This axle does not come with the BOB Trailer bobbins (those are available separately). Or, you can reuse your bobbins from the stock BOB Trailer Quick Release that came with your trailer. - Designed, built, and quality tested in the USA. Proven around the world.
Stan's NoTubes Alloy Tubeless Valve Stems
$23.00
Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.
SRAM Rise 40 Conversion Caps
$23.00
SRAM's Rise 40 conversion caps are the ticket for converting your Rise 40 wheels to a different axle type. You can easily change axle standards with the SRAM Rise 40 conversion cap tool (sold separately).
Stan's NoTubes XD Freehub Conversion Kit (Stan's 3.30 Hubs)
$80.00
This conversion kit allows you to use SRAM's 11-speed mountain cassette on your Stan's NoTubes wheels. Each kit includes an XD freehub, spacer, drive side end cap, and three sealed bearings.
SRAM X0 Hub Conversion Caps
$18.00 - $27.00
SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.
Whisky Parts Co. 50w Rim Decal Kit
$25.00
- Colored rim decal kits to personalize your ride - Decals to fit two (2) 50w 27.5+ rims
Whisky Parts Co. 70w Rim Decal Kit
$25.00
- Colored rim decal kits to personalize your ride - Decals to fit two (2) 70w 26-inch rims
Shimano Dura-Ace 9000 Quick Release
$64.00
Shimano Dura-Ace 9000 Hub Quick Release Skewer. - Axle Type: Standard QR
Shimano 105 5800 Rear Hub Left Cone and Lock Nut Unit
$12.00
-Replacement left side cone and locknut for Shimano 105 FH-5800 rear hub
Stan's NoTubes Spoke Powder Assembly Compound
$13.00
The same spoke thread treatment used by Stan's pro wheel builders is now available to everyone. Stan's SRD Spoke Powder fills the threads of the spoke and functions as both a lubricant during assembly and a thread lock once built. Each bottle contains 24g (.8oz) which will treat approximately 300 wheels. The PTFE powder in Stan's SRD Spoke Powder acts as a barrier, keeping the metal of the nipple from bonding to the metal of the spoke and preventing spoke wind up during build or adjustment. In promoting a smoother turning nipple, the powder also ensures more accurate and consistent wheel builds, with less “ping and pop" during and after the build. The powder also fills the threads of the spoke to act as a thread lock that prevents loosening and de-tensioning and is particularly well suited for mechanically locking nipples such as Sapim's Secure Lock. - Improves tension consistency and overall build quality - Prevents spoke wind up - Offers secure thread lock between spoke and nipple - Prevents corrosion between spoke and nipple - Can be used dry or as a slurry - Works great with mechanically locking nipples
Manitou Hexlock Axle
$39.99
Replacement axles for Manitou forks
Wheels Manufacturing Inc. Axle-34
$38.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 24tpi - Diameter: 9.5mm - Length: 180mm - 1 axle per bag
Sunlite 3-Speed Anchor Adjuster
$3.00
- Replacement adjustable nut for three-speed internal hubs.
Wheels Manufacturing Inc. Freewheel/BB Spacer
$16.50
Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10
Wheels Manufacturing Inc. Axle-17
$36.00
Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Hollow Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 110mm - 1 axle per bag
Serfas Presta Valve Cores (10pcs)
$22.00
Replace your lost, damaged, or worn out Presta valve cores with one of Serfas' new Tire RX valve cores. - 10 Count Presta Core Replacements - Fits All Presta Valves
Zipp Tangente Quick Release Skewer Set
$50.00
Match your Beyond Black hubs, spokes and decals (each sold separately) with skewers from Zipp. - Sold in pairs - Stainless steel: 85 grams/set - Titanium: 78 grams/set
SRAM Rise 40 Conversion Cap Tool
$9.00
SRAM's Rise 40 Conversion Cap Tool will allow you to easily change the conversion caps (sold separately) on your Rise 40 wheels.
Chris King ISO SD QR Front Axle End
$17.50
Chris King ISO SD QR front axle end to pair with QR axles.
Zipp 77/177 Disc Conversion Caps
$18.00 - $28.00
Zipp Speed Weaponry Hub Conversion Caps
Robert Axle Project Kid Trailer Thru Axle
$65.00
Purchase our Kid Trailer axle for your bike, and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.
Page 1 of 4 Next page